QRR0.012G/S/SA is another micro-sized pyrosol aerosol gas suppression system that is made up of iron steel with red paint, it is a very very small automatic fire sticker special for narrow enclosed spaces, such as an electrical panel, Lithium Battery, Coffer, Meter boxes and so on.
Till now, we have installed many quantities of this product in many small spaces for fire protection across various industries.
Our cooperators are SCHNEIDER, SIMENS, DELIXI, VESTAS, TESLA, CHINA MOBILE, CHINA TELECOM, State Grid Cooperation of China, etc.
Wind Turbines, New Energy Vehicles, and Electric Equipment are 3 major fields it can be applied to.
Its basic parameters are as follows:
- Name of This Product: Aerosol gas suppression for small space protection.
- Model Number: QRR0.012G/S/SA.
- Size and Dimension: φ40*H20 mm (Refer to our Installation Manual QRR0.012G-S-SA).
- Installation Hole Spacing: φ4*54 mm.
- Design Density: ≤100 grams per cubic meter.
- Protection Volume: ≤0.12m³.
- Thermal Cord Rated Temperature: 175 ± 5℃.
- Operational discharge time: ≤4 Seconds.
- Activation Current: ≥700 mA (DC).
- Safe Current: ≤150mA (Direct current).
- Electric Activation Time: ≤1 Second.
- Ambient Temperature: -50℃ to +95℃.
- Life Time: 10 Years.
- Warranty Time: 1 to 2 Years.
- Compatibility: it can work with fire alarm systems and gas fire control panels.
Remark: there is a smaller capacity of 7 Grams of Aerosol for 0.07 m3 mall space.
It is a new product in a variety of industries, you can use it in the meter box, in the password box, etc, but you will mostly install it in the below fields：
- Electrical panels in many industries.
- Wind turbines for new energy power generation.
- Lithium battery for new energy vehicles.
- Household field.
- Electric car.
- Electric golf cart.
- Charging pile.
- UPS center.
- Outdoor distribution cabinets.
- Electric forklift.
- Electric logistic truck.
- Electric motors.
- Gasoline refueller
Attention to Transportation, Store, and Installation
- Do not get close to the heat source when it is being in transportation, storage, and installation, please avoid sunlight and rain.
- Do not use the product when the aerosol device’s outer shell is damaged.
- Do not disassemble the device without the permission of the manufacturer.
- People who enter the site must wear gas masks, in case the aerosol device is being in discharging.
Installation and Maintenance
- Take out the installation bracket of the aerosol device and fix it, there should be no obstacles between the aerosol device and the protective objectives. if necessary, the installer can install the auxiliary support also, the auxiliary support should be able to bear at least 5 times the weight of the aerosol device, to make sure the aerosol device is firmly installed.
- When installing, you need to consider avoiding high-temperature areas above 95℃. there should be no obstacles within 0.1m in diameter of the aerosol device.
- Do not disassemble the device without the permission of the manufacturer. The thermal cord should be arranged along where the fire perhaps will occur; it is forbidden to install it at the high-temperature pipelines, in case of is activated by mistake.
- After releasing, the shell/cylinder of the aerosol device is super hot with high temperature, so it is forbidden to touch it and wait until it cools down before you can handle it.
- During its valid time, there is no need to hold yearly quality inspections; The shell/cylinder of the aerosol device needs to be regularly cleaned of dust and dirty according to the actual situations; if it is found to be deformed or damaged, it should be replaced in time; Regularly check wiring for open circuit, short circuit and resistance value of the ignition device and keep records.
- The related losses caused by abnormal installation, maintenance, and use are not within the scope of the company’s warranty.
